Infinite-peripherals SCOM-100 Manual de usuario

SCOM-100, User guide 10 3. Getting started 3.1 Preparing a SIM card Before installing the SIM card, use your

SCOM-100, User guide 11 4. Device operation 4.1 SMS commands The SCOM-100 unit accepts text SMS commands to c

SCOM-100, User guide 12 a: Transition selection (0: No alarm, 1: positive 2: negative 3: both transitions) d

SCOM-100, User guide 13 0630,1,Door is opened; 0630,2,Door is closed Now we have to associate the text messa

SCOM-100, User guide 14 The output LED 2 will switch on and you will hear the relay contact switch to a close

SCOM-100, User guide 15 4.4.4 Pulse digital output A digital output set with a pulse behaves as shown on the

SCOM-100, User guide 16 The command to reset an output after a delay is: 1021,m,n,h,mn 1021: Command ID m:

SCOM-100, User guide 17 The command to configure and set up a time schedule is: 1700,ID,d,P1B-P1D,P2B-P2D,…,

SCOM-100, User guide 18 4.4.8 Clearing the digital output configuration The command clears any output configu

SCOM-100, User guide 19 The 4-20mA input signal is converted by the internal A/D converter in the digital raw

SCOM-100 Alarming & remote control unit User guide Manual version: 2.0, 5/2010 Firmware version: 1.1.5 Copyright © 2006-2010 – I

SCOM-100, User guide 20 4.5.3 Clearing the analog input configuration Any analog input configuration settings

SCOM-100, User guide 21 h: ‘Hysteresis’ value in [%] of the analog input scale (0-20%) for ON/OFF control (n

SCOM-100, User guide 22 5. User administration Up to 20 SMS users can be declared in a user list for an SCOM-

SCOM-100, User guide 23 5.4.1 Set a DI alarm recipient 1102,m,n,id 1102: Command ID m: Module number (0 for

SCOM-100, User guide 24 6. Device status & mode controls 6.1 Setting the device status A SCOM-100 unit ha

SCOM-100, User guide 25 Note: In the case of a rejected command, the error response SMS is always being sent.

SCOM-100, User guide 26 6.6 Setting a GSM PIN An optional SIM card PIN can be set through the following comm

SCOM-100, User guide 27 7. Monitoring capabilities 7.1 Monitoring commands The following command invokes a re

SCOM-100, User guide 28 Select a serial connection, choose the appropriate serial port and press ‘OK’. Sele

SCOM-100, User guide 29 If a connection is established the answer is ‘OK’. If you don’t see your typed charac

SCOM-100, User guide 3 Contents 1. Device overview 5 1.1 Connections 1.2 LED indications 2. Wiring 6 2.1

SCOM-100, User guide 30 8. Appendix 8.1 Command reference 8.1.1 General parameter settings Cmd Description

SCOM-100, User guide 31 8.1.3 Output control & configuration Cmd Description Syntax Comments 1000 Set

SCOM-100, User guide 32 Cmd Description Syntax Comments 1253 Clear PID Control DI cmd,id id:1-4 1255 S

SCOM-100, User guide 33 Cmd Description Syntax Comments 3600 Get RTC Time cmd 3700 Get Time Schedule

SCOM-100, User guide 34 8.3 Technical specifications 8.3.1 Main unit Protection IP20 Temperature range -10°C

SCOM-100, User guide 35 8.3.3 GE-AI-4 Analog Input Expansion module Protection IP20 Temperature range -10°C,

SCOM-100, User guide 36 8.4 Status LED indications 8.4.1 Main unit LED Indication POWER Presence of power s

SCOM-100, User guide 37 8.5 Default parameter values (Factory settings) Parameter Value Device Name SCOM-1

SCOM-100, User guide 38 The module number (m, see sections 4.3 & 4.4) of an expansion module is determi

SCOM-100, User guide 39 8.6.2 GE-AI-4 analog input expansion The input range of each analog input can be

SCOM-100, User guide 4 5.4 Defining specific alarm recipients 5.4.1 Set a DI alarm recipient 5.4.2 Set an AI

SCOM-100, User guide 40 The following table contains the scale and Sensor low/high values for the common rang

SCOM-100, User guide 5 1. Device overview 1.1 Parts identification 1: Start up button 2: GSM antenna connect

SCOM-100, User guide 6 2. Wiring SCOM-100 is a simple device, not requiring special technical background for

SCOM-100, User guide 7 Voltage Current Mode 250VAC 10A AC1 250VAC 1A AC2,3 150VDC 0.5A DC It is recomme

SCOM-100, User guide 8 The circuit displayed on the right side of the page uses an external resistor (Rx) to

SCOM-100, User guide 9 Bridge Vcc to Vex on the main SCOM-100 unit to power a limited number of I/O expansion